Fort Wayne Auto Repair

When you start your vehicle’s engine, there’s another motor that makes that whole process possible.  It’s called the starter, and it’s a small electric motor that gets your vehicle running.  

As you can imagine, it’s quite a chore for a little electric motor to turn over the big engine that powers your vehicle.  And after hundreds of successful starting missions, after a while, it will start to give out.

You’ll know the starter is starting to give up the ghost when it turns too slowly or sometimes doesn’t do anything when you turn on the ignition.  Maybe it makes funny noises like grinding when you try to start your vehicle or maybe there’s just a click. Those are all reasons to get your vehicle over to us so we can see what’s going on. 

A technician will make sure the problem is the starter and not in the battery, a switch, or other electrical component or connections.  If all of those are ruled out, your starter will be replaced.  The technician will also make sure all the cables and connections to the battery are clean and solid.  

Often starter problems come on gradually, and they often give you advanced warning that it’s time to have it fixed—before you find yourself frustrated— and stranded.

Ed's Car Care Center
7811 North Clinton Street
Fort Wayne, IN 46825
2604835721
http://www.edscarcarecenter.com

Ever wonder how your vehicle’s engine is able to take the 12-volts from its battery and ramp that up to as high as the tens of thousands of volts it takes to fire its spark plugs? The secret is something called an ignition coil.  Most newer vehicles have an ignition coil at each cylinder, but older ones have a coil that serves all of the spark plugs. 

There are telltale signs that you have an ignition coil problem.  As you might expect, one symptom is it’s hard to start your engine or it won’t start at all.  If your engine is misfiring or not running smoothly or you see the Check Engine light come on, those all could point to an ignition coil failure.

Several things can contribute to ignition coil trouble in addition to normal wear and tear. Moisture and dirt may have gotten inside the coil, plus the heat and vibration of your engine over time can contribute to them going bad.  Bad spark plugs or plug wires can also be a cause.  

While ignition coils can last 100,000 miles/160,000 km, depending on how you drive and in what conditions.  If you start noticing some of the signs and symptoms just described, it’s a good idea to schedule a visit to see us so a technician can diagnose what’s wrong. Driving too long with an engine misfiring can damage your catalytic converter, and that can be expensive to replace.

A technician will thoroughly check your ignition system and determine where the failure is.  If it’s only one coil that’s bad, it may be the only thing that will need replacing.  If your vehicle has a distributor, it may also need to be replaced.  Properly-working ignition coils will help your vehicle operate at its best and help prevent future engine damage.

Ed's Car Care Center
7811 North Clinton Street
Fort Wayne, IN 46825
2604835721
http://www.edscarcarecenter.com

It's bad enough in cold weather when ice and snow block your visibility.  Add to that fog on the inside of your windows and you could be driving blind.  So here are a few tips on how to keep your windows from fogging up when there's a chill in the air.

You probably know fog is really condensation, when moist, warm air meets a cold surface and turns to liquid.  If your windshield fogs up, you probably turn on your windshield defroster. Most defrosters blow heated air on the windshield glass to warm it up so it won't condense the moisture.  Many also turn on the air conditioning to reduce the moisture. 

That same strategy can work on the rest of the windows.  First, turn up your heater's temperature setting.  The hotter the air, the more moisture it will hold.  Also, turn off the "recirculating" setting since you want all outside air to come in. Then switch on the air conditioning.  It will remove the moisture from the outside  air that it's blowing inside the cabin.  Try cracking a couple of windows to make it easier for the air to flow. This should do the trick pretty quickly. 

There's one other thing to try.  Many vehicles have electric heater elements embedded in the rear window glass (the rear window defroster) and in the outside rearview mirror glass. Make sure to turn those on, too; sometimes they're on the same switch.

For all of these things to work, of course, your vehicle's components have to be maintained so they'll do the things they're designed to do.  And you didn't think it was important to have your air conditioning working in the cold weather months! 

One final tip.  Keep the insides of your windows CLEAN.  Oil and dirt on the glass give the water molecules something to latch on to.  That ought to clear up this problem.

Ed's Car Care Center
7811 North Clinton Street
Fort Wayne, IN 46825
2604835721
http://www.edscarcarecenter.com

If your vehicle creaks and squeaks when you drive down the road, it may mean that some of the metal parts are rubbing against each other and need to be lubricated.  Those could be parts of the suspension, steering system and the drivetrain. 

Years ago, most vehicles had to have their chassis (what you think of as the frame) regularly lubricated.  Newer vehicles are made with what some call "lifetime lubrication," but there are still parts of the chassis that need to be maintained with lubricants.  Your service advisor can help you know when that needs to be done.

In your owner's manual, the vehicle's manufacturer lists components that need regular maintenance. Things like u-joints, steering joints, sway bars, bushings and joints in the suspension. Some of them may have that "lifetime lubrication," while others may not. When you bring your vehicle in for service, a technician will look for any parts that have grease fittings.  They will inspect these components, clean the fittings so dirt and other contaminants won't be forced into the part and then lubricate them with a lubricant that meets the manufacturer's specifications. 

Sometimes a chassis lubrication is done at the same time as an oil change.  That's also an ideal time for the technician to check other parts of your vehicle that may need attention.  That could include greasing other parts such as the fuel door, trunk and door hinges, suspension springs and door latches.

Times have changed since the days when a "lube" job was synonymous with an oil change. Depend on your owner's manual and advice from your service advisor to know when "grease" is the word—and appropriate for your vehicle.

Ed's Car Care Center
7811 North Clinton Street
Fort Wayne, IN 46825
2604835721
http://www.edscarcarecenter.com

For drivers, S stands for safety.  And there are three other words that start with S that are all equally important: starting, stopping and steering. For your vehicle to be at its safest, all three functions must be in top shape. 

Steering is one of those things we take for granted.  After all, you turn the wheel and your vehicle changes direction. But sometimes you might notice your steering is a little off.  Maybe you've noticed you turn your wheel slightly and your vehicle doesn't turn. You may feel a little vibration in the wheel that increases when you go faster.  You may hear a little squeak from the wheels when you steer and you may notice your tires aren't wearing evenly.

These are signs that your tie rod ends may be failing. Tie rod ends help connect your vehicle's steering mechanism to the wheels.  They can wear out after you've hit one too many potholes or just from constant use.  They can cause sloppy steering and loose handling, and they should be replaced when they've reached the end of their life span.

If you notice any of these things happening on your vehicle, bring it in to us so a technician can check it out.  There are a couple of different types of steering, recirculating ball steering and the one most of the latest vehicles have, rack and pinion. When we replace your tie rod ends, we will remove and replace the old ones and adjust them to meet your vehicle manufacturer's specifications.

Tie rod ends should often be replaced in pairs, and your vehicle should be aligned afterwards.  Keep your steering working the way it's supposed to, and your vehicle will be sure to steer you right.

Ed's Car Care Center
7811 North Clinton Street
Fort Wayne, IN 46825
2604835721
http://www.edscarcarecenter.com

When you head out to your vehicle after it's been parked and notice oil leaking underneath it, that's something to have looked at right away.  Oil leaks mean your oil level is probably low and running a vehicle in that condition can lead to expensive repairs.

While there are many reasons oil leaks develop, one possibility is a bad valve cover gasket.  Vehicle engines have a cover bolted over the spot where the engine valves are, and that cover keeps the oil inside the engine. In between the cover and the engine is a gasket that keeps that seal tight.  But after many years of high engine temperatures and vibrations, that gasket or the bolts that hold on the valve cover can fail or loosen, and oil can leak.

You may see dirty oil on the valve cover in the engine compartment, near the spark plugs, or around the bolts that hold the valve cover on.  All those are signs of leakage and time to bring your vehicle in for our technicians to check out.

In some vehicles, taking off the valve cover and replacing the gasket is a relatively easy job. In some models, though, other engine parts are located near that part of the engine and must be removed to get at the gasket, so repair costs can vary widely.

The technician will measure to make sure the valve cover isn't warped so it can be reused. If it is warped, they'll recommend replacing it with the gasket.  

While the technician has that area of your engine accessible, they will also check to see if other components need replacing at the same time, which could save you money.  And because valve cover gaskets usually fail in older vehicles, the technician will check for other oil leaks then, too. 

One of the best ways to be sure your valve cover is doing its job is to have your vehicle regularly maintained.  The technician will periodically look over your engine compartment and make sure you know when things are showing signs of age and wear BEFORE they fail and leave you stranded.

Ed's Car Care Center
7811 North Clinton Street
Fort Wayne, IN 46825
2604835721
http://www.edscarcarecenter.com

Ever wonder how your vehicle’s transmission is connected to your wheels? After all, when you hit a pothole or some other uneven part of a road’s surface, there has to be something that can maintain the connection between the transmission and the wheel yet keep everything moving at the same speed. 

That very cool device is called a CV joint, a kind of driveshaft running to each wheel.  The CV stands for constant velocity because it keeps the drive wheels moving at a constant speed (velocity).  They’re used mostly on front-wheel drive vehicles but also in rear-wheel and all-wheel drive vehicles.

The joints move up and down and adjust to bumpy surfaces.  Plus, they are covered in a rubber boot which protects them from road debris and also holds lubrication in.  There’s a CV joint and boot on the transmission side and one on the wheel side.  Unfortunately, the spot that usually fails first is that rubber protective cover (the boot).  After a lot of wear, tear, bumps, road hazards, heat, and you name it, the rubber rips and the lubrication leaks out.  At that point, it must be replaced. 

Here are signs to tell if your CV joint is bad.

• Your vehicle is pulling to one side as a wheel loses power or you feel a vibration while driving.
• You see grease on the inside or edge of your tires.  
• Your front tires won’t point in the same direction.
• You hear grinding or clicking when you turn.

Sometimes if a broken boot early is caught early, a technician can pack in new grease and replace just the boot.  But if the lubrication has leaked out and the joint is already wearing badly, the CV and boot both have to be replaced.  Give your vehicle the boot (as in a new boot) and CV joint, and you’ll be back on the road to your next destination.

Ed's Car Care Center
7811 North Clinton Street
Fort Wayne, IN 46825
2604835721
http://www.edscarcarecenter.com

A driver brought her vehicle into the shop the other day and told us how she was getting lousy fuel economy and that the engine was running rough.  Plus, the Check Engine light was on.  Our technician checked the code the engine had generated (why the Check Engine light was on) and found the problem.  It was a faulty Mass Air Flow sensor, MAF sensor for short.

This MAF sensor is an important part of your vehicle.  What it does is calculate the amount of air going into your engine.  As you may know, air is taken into your engine where it's mixed with fuel.  Then, the spark plugs fire, that explosive fuel/air mixture detonates, and all these sequential explosions together provide the power to get your vehicle moving down the road. 

It makes sense that if the MAF sensor isn't sending the engine's computers the correct information on the amount of air going in the engine, the fuel/air mixture isn't going to be right. It will either too rich (too much gasoline for the amount of air) or too lean (not enough gasoline for the amount of air).

In this driver's case, the MAF sensor was damaged and needed to be replaced.  Another thing that may cause the MAF to give an incorrect reading is if its wires are dirty or faulty.  So, replacing or cleaning the wires important as well.

Other symptoms that your MAF sensor is bad? If your engine hesitates when you step on the gas, it stalls, or your vehicle is jerky when you accelerate. 

A malfunctioning MAF sensor is not just bad for performance.  Driving with your vehicle in that condition can cause more damage to your engine.  When you bring your vehicle in for us to check, a technician will thoroughly examine your engine to make sure all issues are taken care of.

Ed's Car Care Center
7811 North Clinton Street
Fort Wayne, IN 46825
2604835721
http://www.edscarcarecenter.com

If you've ever walked into your garage and noticed it smelled like gasoline, pay attention. Gasoline can be dangerous, both from the health problems fumes can cause and the fire danger gasoline presents. 

There are many things that can cause a vehicle to give off a gasoline odor.  One of the easiest to track down is the gas cap.  It could be missing or it doesn't seal well any more (they do wear out).  That can also cause the Check Engine light to light up, so those are clues to tell your service advisor when you take it in for diagnosis.

Another thing that can cause the Check Engine light to come on and produce a gasoline smell is the fuel filler neck. It's the part that goes from the place you put your fuel in to the gas tank. Over time, these can wear out and fail (they're made out of rubber or metal).  They can leak gasoline, too.

It's always a good idea to check the garage floor for any gasoline puddles.  Note the location of the puddle in relation to the vehicle. If it's near the back, that's possibly the fuel filler neck or the gas tank leaking.  In the middle of the vehicle? May be fuel lines.  Near the front? Could be fuel injectors (or carburetor if you have one) or fuel pump. 

There are other causes of gas odors, and you need an expert to figure out the source soon.  Gasoline leaks are nothing to play around with.  Gasoline is flammable, potentially explosive and its fumes can damage your lungs. A trained technician can pinpoint the cause and get your garage back to smelling like a normal garage again.

Ed's Car Care Center
7811 North Clinton Street
Fort Wayne, IN 46825
2604835721
http://www.edscarcarecenter.com

When you start up your gasoline engine car, you may not know that it's using the same ignition principles as it has for decades.  You have spark plugs that require enough power so a spark can jump across a gap at its tip.  Years ago, a vehicle's 12-volt system had to produce 15,000-25,000 volts to do that, so engineers came up with something called an ignition coil that bumps up the voltage. It also has to be done at just the right interval called timing.

The first systems had a distributor, a mechanical device with a rotating disc that switched the power to the ignition coil on and off.  That higher voltage then was sent to the spark plugs at the correct time interval. But the mechanical "points" had to be replaced and adjusted every 12,000 miles/20,000 kilometers.  Engineers later replaced the switching mechanism with solid state ones, but they still needed replacement after 120,000 miles/200,000 kilometers.

The next evolution came in the 80's when the distributor was replaced with a couple of sensors which talked to a computer.  This "DIS" (distributor-less automotive ignition system) was a big advance.  Plus, it didn't use just one ignition coil for all the cylinders.  It had coil "packs" that each provided spark to two cylinders.  That way, the voltage could be boosted even higher, to 30,000 volts, which helped engines be able to ignite a leaner fuel/air mixture.

Recently have come even more improvements.  Now instead of coil packs, there's a coil that's attached to each spark plug.  No more spark plug wires means less maintenance. Plus, a stronger, hotter spark of 50,000 volts can make an engine more reliable, increase fuel economy and reduce emissions.

No matter what ignition system your vehicle uses, your vehicle service facility has a staff of technicians trained to work on the latest technology.  Make sure to have your vehicle maintained regularly so you can take full advantage of these modern engineering marvels.

Ed's Car Care Center
7811 North Clinton Street
Fort Wayne, IN 46825
2604835721
http://www.edscarcarecenter.com